7 things to check before signing hvac proposal
7 Things to Check Before Signing an HVAC Proposal
Replacing a furnace, heat pump, or air conditioner is a major investment. Unfortunately, comparing HVAC proposals can be difficult because two contractors may be quoting very different scopes of work—even when the equipment appears similar.
A lower price does not automatically mean a worse installation, and a higher price does not automatically mean a better one.
The key is understanding what you are actually getting for the money.
Before signing an HVAC proposal, here are seven things worth checking.
1. Was the system properly sized?
One of the most important questions is also one homeowners often overlook:
How did the contractor determine what size equipment your home needs?
Heating and cooling equipment should be selected based on the needs of the home—not simply by replacing the existing system with the same size.
A proper load calculation considers factors such as:
- square footage
- insulation levels
- window size and orientation
- air leakage
- ceiling height
- local design temperatures
- number of occupants
- other characteristics of the home
In the HVAC industry, this is commonly referred to as a Manual J load calculation.
Oversized equipment can create comfort, humidity, noise, efficiency, and equipment-cycling problems. Undersized equipment may struggle to maintain the desired temperature during extreme weather.
Question to ask:
“Was a Manual J load calculation performed, and can you show me the heating and cooling loads?”
2. Are the exact equipment model numbers listed?
A proposal that simply says “16 SEER heat pump” or “high-efficiency furnace” leaves out a lot of information.
Ask for the exact manufacturer and model numbers of the equipment being installed.
This allows you to verify things such as:
- system capacity
- efficiency ratings
- single-stage, two-stage, or variable-speed operation
- manufacturer warranty
- cold-weather performance
- whether the indoor and outdoor equipment are properly matched
Two systems from the same manufacturer can have dramatically different capabilities and prices.
Without model numbers, it can be difficult to know whether two contractors are actually proposing comparable systems.
Question to ask:
“What are the exact model numbers of the indoor and outdoor equipment included in this proposal?”
3. Was the duct system evaluated?
The best heating and cooling equipment in the world cannot perform properly if the duct system cannot move the required amount of air.
Existing ductwork should be considered when replacing HVAC equipment.
Potential issues include:
- undersized ducts
- excessive static pressure
- damaged or disconnected ducts
- restrictive filters
- poorly sized return air
- air leakage
- inadequate supply airflow
A contractor may not need to replace your duct system, but the proposal should make clear whether the existing ductwork was evaluated and whether modifications are recommended.
Question to ask:
“Was my existing duct system evaluated to make sure it can handle the airflow required by this equipment?”
4. What installation and commissioning procedures are included?
Equipment selection matters, but installation quality matters just as much.
For heat pumps and air-conditioning systems, good installation practices may include:
- flowing nitrogen while brazing refrigerant lines
- properly evacuating the refrigeration system
- verifying vacuum levels
- confirming refrigerant charge
- checking airflow
- measuring static pressure
- testing system operation
- completing final startup and commissioning
These details may not always appear on a proposal, but they are worth asking about.
One example is brazing with nitrogen. Flowing nitrogen through refrigerant tubing during brazing helps reduce oxidation and contamination inside the refrigerant lines.
A professional proposal should give you confidence that the contractor has a defined installation and startup process.
Question to ask:
“What commissioning procedures will be performed before the system is turned over to me?”
5. Are permits, electrical work, and other installation costs included?
Two HVAC quotes may look thousands of dollars apart simply because one includes work that the other does not.
Look for details about:
- permits
- electrical circuits or breakers
- refrigerant line sets
- condensate drainage
- equipment pads
- thermostats
- duct transitions
- equipment removal and disposal
- gas piping
- venting
- crane or difficult-access charges
- required inspections
If something is not listed, that does not necessarily mean it is excluded. It means you should clarify it before signing.
Question to ask:
“Does this price include everything required to complete the installation, including permits and electrical work?”
6. What warranties are actually included?
HVAC warranties can be confusing because several different warranties may apply.
A proposal may include:
Parts warranty — usually provided by the equipment manufacturer.
Labor warranty — typically provided by the installing contractor.
Compressor or heat-exchanger warranty — sometimes different from the general parts warranty.
Maintenance coverage — sometimes included for the first year or bundled into a membership program.
Do not assume that a “10-year warranty” means both parts and labor are covered for 10 years.
Ask exactly what is covered, who provides the warranty, and whether equipment registration or ongoing maintenance is required.
Question to ask:
“What are the parts and labor warranties, and are there any requirements I need to meet to keep them valid?”
7. Compare the entire proposal—not just the price
Price matters. But it is only one part of an HVAC proposal.
Consider the entire scope:
- equipment
- sizing
- efficiency
- installation procedures
- ductwork
- permits
- electrical work
- warranties
- maintenance
- rebates
- financing
- contractor responsibilities
One proposal may cost more because it includes additional electrical work, a longer labor warranty, duct modifications, better equipment, or a more complete commissioning process.
Another proposal may simply be less expensive.
Neither situation automatically tells you which contractor you should choose.
The important thing is understanding why the prices are different.
A good proposal should help you make an informed decision
You should not need to be an HVAC technician to understand what you are buying.
Before signing, make sure you can answer three basic questions:
What equipment am I getting?
What work is included?
What protections do I have after the installation?
If the proposal does not answer those questions, ask for clarification before moving forward.
Already have multiple HVAC quotes?
South Sound HVAC Guide’s AI Quote Comparison Tool can help organize your proposals side by side and highlight differences in equipment, warranties, installation details, permits, ductwork, rebates, and other important items.
The tool does not choose a contractor for you. Its purpose is to help you identify what is documented, what may be missing, and what questions you may want to ask before signing.
Know what you’re buying before you sign the HVAC contract.
Use our AI-assisted comparison tool to organize what each contractor actually documented.
Compare HVAC quotes
